SouthCentral  ECC

Focus area

Products, Specialty Tools, & Testing

A focused product line aimed at the parts that go into — and onto — high-voltage distribution equipment. Three product families: high-voltage bushings rated 150 BIL and above, shear bolts for controlled-failure applications, and specialty tools for hardware our customers can’t service with off-the-shelf sockets.

A high-voltage polymer bushing assembly on a walnut display surface

High-voltage bushings (150 BIL+)

Specialty bushings built for high-voltage applications — 150 BIL and above — where standard distribution-class bushings can’t meet the dielectric or mechanical demands. Designed around the failure modes our principals have spent careers cataloguing.

Long stainless shear bolt with forked clamp piece

Shear bolts

Shear bolts engineered for controlled-failure applications on distribution equipment — predictable break torque, repeatable performance, and tolerances that hold up in the wet, hot, and salt-laden environments our customers actually operate in.

Power-Torque 5/8" specialty socket fitted to a brass sampling valve

Specialty tools

Specialty sockets and field tooling for non-standard fastener heads on legacy and current transformer hardware — sized to fit the geometries linecrews and shop technicians keep encountering on real assets, not catalogue assumptions.

Inside the lineup

Specialty tools, sampler valves, and (placeholder for) shear bolts. The shielded high-voltage bushing pictured at the top of the page is one example of the bushing line.

Spade and clamp-style torque sockets
Spade & clamp-style torque sockets.
Stainless-steel sampler Schrader valve, bottom-view assembly
Stainless-steel sampler Schrader valve.
Stainless-steel sampler Schrader valve, galvanic-corrosion mitigation
Schrader valve — galvanic mitigation.
Sampler-valve fitting with wing-screw, lock washer, and hex nut on a workshop bench
Sampler-valve fitting & hardware — bench inspection.
Shear bolts designed for manual wrenches or battery-operated impact wrench applications
Shear bolts — manual or battery-impact wrench applications (1 of 2).

Pressure-test & qualification rig

On the bench: the team's pressure-test rig, used to qualify tank assemblies and gauge field work against shop-floor measurements.

Pressure-test rig venting steam during a tank test
Pressure-test rig venting during a tank test.
Engineer torquing a bolted fixture into the top of a cylindrical pressure-test rig
Torque-down on the pressure-test rig.
Fluke clamp meter taking a load reading on the pressure-test rig
Clamp-meter load reading on the rig.
Infrared thermometer reading the cap of the pressure-test rig
IR thermometer reading on the rig cap.

Bushing development & material testing

Accelerated material-capability testing of bushing designs against various chemicals, run on the shop bench.

Bushing development — material capability testing, 1 of 3
Material capability testing (1 of 3).
Bushing development — material capability testing, 2 of 3
Material capability testing (2 of 3).
Bushing development — material capability testing, 3 of 3
Material capability testing (3 of 3).
Conventional epoxy bushings staged for high- and low-voltage testing
Conventional epoxy bushings — high & low voltage testing.
Bushing development — cold-weather and hydrostatic high-pressure / high-temperature test setup
Bushing -40°C freeze through hydrostatic high P/T test (4 of 6).

Bench-side testing

Material and instrument testing on the shop bench — sampling, conditioning, and instrument-and-leads setups for unit-under-test work.

Two engineers running bench-side material tests with sample bottles and a laptop
Bench-side material testing.
Bench-side instrument setup on plywood with leads attached to a unit-under-test
Test-instrument setup with leads.

Need one of these for a project?

Tell us the application — voltage class, fastener pattern, or the failure mode you’re trying to design around — and we’ll work through whether one of our lines fits or whether a custom build makes sense.

Schedule a consultation